← All articles Flood Map for Planning: How to Read and Use One Knowledge Centre

Flood Map for Planning: How to Read and Use One

Last Updated: 22 October 2026

Quick Summary

A flood map for planning shows land at risk of flooding from rivers and the sea, split into Flood Zones 1, 2 and 3 by likelihood. It is a screening tool published by the Environment Agency: it flags risk and triggers planning conditions, but it does not tell you whether your site will actually flood.

  • Flood Zone 3 is land with a 1 in 100 or greater annual chance of flooding from rivers.
  • The map excludes surface water, sewers, groundwater and reservoirs, which sit on separate maps.
  • You need a flood risk assessment in Flood Zone 2 or 3, or where the site is over one hectare.
  • Screenshot the map with the date visible in case the Environment Agency updates it mid-application.
  • A flow path across your site usually means a condition requiring a drainage strategy with SuDS.

Table of Contents

What a Flood Map for Planning Actually Shows

A flood map for planning shows the land at risk of flooding from rivers and the sea, split into zones by likelihood. It does not tell you whether your site will flood. It tells you what the planning system will ask you to prove.

That distinction matters more than most applicants realise. A flood map for planning is a screening tool. It flags risk, and the flag triggers conditions.

Here is what the map actually contains:

  • Flood Zone 2: land with a medium chance of flooding, between 1 in 100 and 1 in 1,000 each year from rivers, or 1 in 200 and 1 in 1,000 from the sea
  • Flood Zone 3: land with a high chance, 1 in 100 or greater from rivers, or 1 in 200 or greater from the sea
  • Flood Zone 1: everything else, low probability

The map is published by the Environment Agency and updated periodically. You can view it through the Environment Agency flood map for planning service.

One warning before you go further. The map shows the risk from rivers and the sea. It does not show surface water, sewers, groundwater, or reservoirs. Those sit on separate maps, and planners check them too.

How to Read a Flood Map Before You Apply

Start with the postcode, not the outline. Search your site address, then zoom until the red boundary of your plot is visible against the zone shading. If the shading clips even a corner of the site, treat the whole site as affected until an assessment proves otherwise.

Next, check the flood risk from other sources. The Environment Agency publishes a separate flood risk map covering surface water, reservoirs and groundwater. Read both before you spend money on drawings.

Then answer three questions in writing:

  1. Which flood zone covers the site, and what percentage of the plot sits inside it?
  2. Is the site within 20 metres of a main river? If yes, the Environment Agency becomes a consultee.
  3. Does the surface water map show ponding on or near the proposed building footprint?
A person at a desk studying a printed map with a laptop open nearby, pencil in hand and notes on a notepad, in a bright home office
A person at a desk studying a printed map with a laptop open nearby, pencil in hand and notes on a notepad, in a bright home office

A common mistake is reading the map at the wrong scale. At national zoom, a site can look safely in Zone 1 when the detailed view shows it straddling Zone 2. Always zoom to the largest scale available.

Pro Tip Screenshot the map at your chosen zoom with the date visible. If the Environment Agency updates the map mid-application, you have a record of what you relied on when you submitted.

Flood Zone 2 and 3: What the Categories Mean for Your Site

Flood Zone 3 is not a ban. It is a test. The National Planning Policy Framework and its planning practice guidance on flood risk set out a sequential test: development should go in areas of lowest flood risk first. If your site is in Zone 3, you must show there is no reasonably available Zone 1 or Zone 2 site.

Zone 2 sits in the middle. Many householder applications in Zone 2 pass with a simple flood risk assessment and a finished floor level above the design flood level.

Zone 3 splits further in practice. Some parts carry a functional floodplain designation, land that has to store water in a flood. Building there is heavily restricted, and only water-compatible uses are normally acceptable.

Zone Annual chance of flooding Typical planning consequence
Zone 1 Less than 1 in 1,000 No flood risk assessment usually needed
Zone 2 1 in 100 to 1 in 1,000 (rivers) Flood risk assessment required, sequential test likely
Zone 3a 1 in 100 or greater (rivers) Assessment plus exception test for some uses
Zone 3b Functional floodplain Development normally refused

The category decides the paperwork, not the outcome. We have seen small extensions approved in Zone 3 with the right mitigation, and refused in Zone 2 because the applicant ignored the surface water map.

Checking the Surface Water Flood Map

Surface water flooding is the risk most applicants miss. It happens when rainfall overwhelms drains and runs over ground. It has nothing to do with rivers, so the river map stays silent about it.

The surface water map grades risk from high to low. High-risk areas show where water would pond in a downpour. Planners increasingly ask for this evidence even on sites in Flood Zone 1.

Look for three things:

  • Flow paths crossing the site, which show where water travels
  • Ponding areas near proposed floor levels or access routes
  • Existing drainage capacity, since new hard surfaces add runoff

If the map shows a flow path through your proposed extension, expect a condition requiring a drainage strategy. That usually means Sustainable Drainage Systems, or SuDS: permeable paving, soakaways, or attenuation tanks that hold water back.

Watch Out Paving over a surface water flow path without mitigation is one of the most common reasons for a drainage condition or refusal. Water has to go somewhere. If you block its route, the planner will ask you to prove where it now goes.

When You Need a Flood Risk Assessment for Planning

You need a flood risk assessment for planning when your site sits in Flood Zone 2 or 3, or when it is over one hectare in area, or when surface water risk is significant. Householder extensions in Zone 1 with no other risk usually do not need one.

The assessment is a written report. It sets out the flood sources, the depth and frequency of flooding, the site's vulnerability classification, and the mitigation you propose. It goes to the local planning authority, and to the Environment Agency or Lead Local Flood Authority where they are consultees.

Get in touch Today →

What most guides miss is that the assessment is read by two different audiences. The planner checks policy compliance. The drainage engineer checks whether your numbers hold. A report that satisfies one and not the other comes back with conditions.

Our team prepares flood risk assessments and drainage designs that answer both readers, from site visit through to council approval.

Planning Scenarios: How Different Projects Use Flood Map Data

A rear extension in Zone 2 needs a short assessment and a raised floor level. A new build in Zone 3 needs the sequential test, the exception test, and a drainage strategy. A commercial scheme near a main river needs early Environment Agency engagement.

Three worked examples:

  • Domestic extension, Zone 2: the map shows the garden in Zone 2, the house in Zone 1. The assessment confirms the extension sits above the design flood level. Approval with a floor level condition.
  • New dwelling, Zone 3a: the sequential test fails because no Zone 1 plot exists locally. The exception test passes on sustainability grounds, with flood-resilient construction and safe access above the flood level.
  • Change of use, Zone 1 with surface water path: no river risk, but the surface water map shows a flow path. A drainage strategy with attenuation gets the condition discharged.

The map is the starting point for all three. The route through planning differs every time.

Common Flood Map Terminology Explained

Flood map for planning: the Environment Agency map showing river and sea flood zones used to screen planning applications.

Flood Zone 2: land with a medium annual chance of flooding, between 1 in 100 and 1 in 1,000 from rivers.

Flood Zone 3: land with a high annual chance, 1 in 100 or greater from rivers.

Functional floodplain: land that must store flood water, where development is tightly restricted.

Sequential test: the policy test requiring development in the lowest flood risk area available.

Exception test: an additional test for certain development types in higher risk zones.

Lead Local Flood Authority: the council body that consults on surface water drainage for major applications.

Sustainable Drainage Systems (SuDS): drainage that manages runoff by holding, slowing, or soaking away water.

Design flood level: the modelled water level a development must be protected against.

Finished floor level: the height of the building's ground floor, set above the design flood level where required.

Frequently Asked Questions

How do I use the flood map for planning?

Enter your site's postcode or grid reference into the government flood map for planning to see which flood zone it falls in. The map shows your site's risk from rivers and the sea, plus areas benefiting from flood defences. Save or screenshot the result, note the zone number and any nearby watercourses, then compare it with your local planning authority's requirements. If the site sits in flood zone 2 or 3, or covers a hectare or more in zone 1, you will usually need a flood risk assessment.

Does a flood map result mean I need a flood risk assessment?

Not always. Sites in flood zone 1 under a hectare generally do not need one unless surface water or other sources are flagged. Flood zone 2 and 3 sites almost always do, and so do sites of a hectare or more in zone 1. The flood risk assessment for planning sets out the risk from all sources, how your development affects flood storage, and what mitigation you will use. Your local planning authority confirms the exact requirement for your application.

What should I do if the map shows a flood risk?

Do not assume the project is blocked. First identify the source: river, sea, surface water or groundwater. Then check the sequential test, which asks whether a lower-risk site is reasonably available. If you stay, you will need a flood risk assessment with finished floor levels raised, flood-resistant construction and safe access and egress. Early drainage and flood advice usually saves redesign later, so speak to a specialist before submitting.

How accurate is the flood map for planning?

The map is a screening tool, not a site survey. It is built from national models and its boundaries are indicative, so a site on the edge of a zone can fall either side once detailed modelling is done. It also does not replace a site-specific assessment of surface water, groundwater or drainage. Treat the result as a starting point and confirm the actual risk with a flood risk assessment before you rely on it for design or planning.


Flood map data changes, council policies shift, and a site that passed last year may need a fresh assessment now. The map tells you where to look; the assessment tells you what to do about it. If you want that second part handled properly, get in touch with The Drainage Designers. We cover site visits, flood risk assessments, drainage design, and council approvals nationwide, with a transparent customer charter and a fixed scope agreed before we start.